There are no reliable, objective and simple methods today for measuring pain in horses. The purpose of this study was to evaluate and describe measuring of mechanical nociceptive threshold (MNT) values with a pressure algometer in clinically pain free riding horses at the riding school of Strömsholm. In this study there were 24 horses. Tape recording and electromyelografi (EMG) was used in an attempt to increase objectivity in the examination. MNT increased with age, however sex and colour had no influence.

Two different methods for measuring biogas production were used, gas meter and gasbags. The gas meters were electronic and counted each time a certain gasvolume passed through them. The gasbags collected the gas that hade passed through the gas meter until a manual measuring could be done. The two different methods gave the same result for a volume at three liters but for a volume around 0,2 liters they did not. Accuracy and precision for the gasbags was more exact than for the gas meters even if the method was difficult with a lot of different elements that could affect the result.

Usability studies are not a central field of research in library and information science. Although literature in library and information science treats the importance of usable user interfaces quite extensively, the literature does not significantly treat potential problems in measuring usability. The aim of this master thesis is to investigate, through a critical analysis, the methods used when conducting usability studies in library and information science. The critical analysis is based on potential problems in measuring usability identified through a literature review from the field of studies Human-Computer Interaction, the concept of usabilitys original domain. The material which is to be analysed, is chosen from one library and information science journal Journal of the American Society for Information Science and Technology.

The mining company LKAB extracts iron ore in three areas in the north of Sweden, Kiruna, Malmberget and Svappavaara. The iron ore is refined and in the pelletizing plants the material is rolled to finished pellet product. The different steps of pelletizing plants causes among other things emissions to the air. It occurs occasionally stops in the production and the emissions are vented via an emergency chimney without purification. The aim for this work is to look into how LKAB may improve their monitoring of air emissions and control of ambient air quality and the analysis methods which are suitable for measuring.

This Master Thesis has been conducted as an assignment of the Swedish Defence MaterialAdministration and the Swedish Armed Forces and aims to examine the Target Location Error(TLE) of a Forward Observer System. The targeting accuracy of the system is vital if the systemis to be used as a sensor for precision munitions. The analyzed system, EOI (FOI 2000), wasdelivered to the Swedish Armed Forces in 2007. The targeting sequence starts with deciding theposition of the system with a GPS-receiver, continues with methods where the north direction issettled and ends by measuring the distance, direction and elevation to the target. When allparameters have been measured the system calculates the position of the target.

The student project Elba at KTH started in 2011 and is a project where a battery driven prototype car is developed. The vehicle competes in Eco Shell Marathon in Rotterdam, Holland. In this competition the vehicle that travels a certain distance including several starts and stops with the lowest energy consumption wins. To minimize the consumption is therefore very important, which requires knowledge of the vehicles energy losses.A vehicle's energy losses depends on several factors and can be divided into the powertrain efficiency and the driving resistance. The driving resistance can then be divided in to rolling and air resistance, if smaller losses like vibrations are ignored.

At present day there are several different methods for measuring of paved surfaces.The most common methods today are measuring with a total station, the GlobalNavigation Satellite System (GNSS) and terrestrial laser scanning (TLS). Recently thedevelopment of unmanned aerial vehicles, known as drones, has increasedexponentially and today there are several ways of using drones for measuring surfacesby photographing and laser scanning.This thesis contains a comparison between the methods terrestrial laser scanning(TLS), and unmanned aerial vehicle photogrammetry (UAV). The measurements havebeen applied on two different test surfaces, one of asphalt and one of gravel. Thepurpose of the comparison is to investigate whether the airborne photogrammetry isequivalent accurate in its height levels as the terrestrial laser scanning. For thecomparison to be more extensive, these two methods have not only been comparedin precision but also in the areas of ease of use and economy.The precision was analyzed by comparing the height levels in randomly placed controlpoints on the test surfaces.

Control and comparison of various cleaning methods on restaurants in Södra RoslagenThe purpose of this report is to find out and analyze the efficiency of cleaning methods in restaurant kitchens. The investigation was carried out through unannounced inspections at 89 restaurants in Södra Roslagen (municipality of Danderyd, Täby and Vaxholm). ATP-measuring was done on a plate, a knife, a bench surface and a cutting board. The ATP-method measured the amount of food residue on equipment and working surfaces after cleaning, with a luminometer and swabs. Restaurant staffs were asked to describe in detail how and when the last cleaning was carried out on the surface.

Skin temperature is detected through signals in unmyelinated C-fibers and thin myelinated A?-fibers in the peripheral and central nervous system. Disorders in thin nerve fibres are important and not rare but difficult to diagnose by the most common neurophysiological methods. In this pilot study different methods for quantitative sensory testing, QST, were compared to give some ideas about which method could be the most efficient to use in order to point out injuries of the sensory system in clinical practice. The comparison was made between Békésy (separate warmand cold thresholds) and Marstock test (combined warm and cold thresholds).

A discussion regarding the alignment and measuring procedure of propeller shafts has arose due to the competing situation in the industry, and higher standards from the customers. An estimation of the deflection of shafts in different alignment situations has been made with help of FEM-analysis and beam theory. This has been analyzed and compared with the experience from Rolls-Royce AB suppliers of shafts. An evaluation of measuring protocols has been made and the result indicates that there is a correlation between the deflection of the shaft and the run out. Results from a measuring test performed by Balino, Spain, verifies this conclusion.

In this bachelor thesis, diagnostic methods for one of Siemens stem inlet control valves have been developed. The work has taken place during ten weeks at Siemens Industrial Turbomachinery AB in Finspång. The company produce steam- and gas turbines and also provides service and maintenance. The purpose with this project has been to develop diagnostic methods that oversee the health of the control valves. By using the developed methods you will know when it?s time for maintenance.

A discussion regarding the alignment and measuring procedure of propeller shafts has arose due to the competing situation in the industry, and higher standards from the customers. An estimation of the deflection of shafts in different alignment situations has been made with help of FEM-analysis and beam theory. This has been analyzed and compared with the experience from Rolls-Royce AB suppliers of shafts. An evaluation of measuring protocols has been made and the result indicates that there is a correlation between the deflection of the shaft and the run out. Results from a measuring test performed by Balino, Spain, verifies this conclusion.

The report describes a measuring method for analysis of energy consumption measurement in microwave ovens. Concurrently that the awareness of the environment evolves the demands are growing for more power saving products. This is also counting within the Home Appliance business, which is Whirlpools business area. Whirlpool is therefore interested of launching microwave ovens with documented low power consumption. To be able to implement this, both asserted measuring equipment, that fulfils all demands, and a standard procedure is required.

This thesis deals with different methods for measuring moisture-related dimensional changes ofwood. Typically relative humidity is measured to determine if the ambient climate around anobject is harmful to it or not. Values between 40 to 65% RH are recommended for hygroscopicmaterials. To know how a wooden object actually reacts to changes in the surroundingenvironment requires methods that involve the object itself. Because of the wood anisotropy,differences in wood structure, finishes and other restraints, it is not always possible to predict themovements.This paper addresses various measurement methods, primarily methods that have been testedin the field of conservation, with examples of their use.

This report describes a study of two different methods to achive the best possible result in setting out apartment details. These two methods are the setting out of details with a measuring tape from baselines and the setting out procedure with an instrument (totalstation).Through our knowledge in surveying and mapping technology and help from a carpenter, this investigation has been implemented. The setting out using a tape has been performed by letting the carpenter to set out windows, bathroom and water- and drain-details from baselines and drawing. The setting out using a surveying instrument was carried out by means of a Trimble Total Station. These two methods have been compared in order to detect and show the difference that occurs.The report shows the investigation background story from the practice of Swedish Mätcenter in Karlstad.A result of differences in accuracy and time is described in the report, as well as their theoretical consequences.